SUN 6800/4810/4800/3800 systems management manual notes

SUN 6800/4810/4800/3800 systems management manual notes
system controller procedures Wizard

This chapter step by step> Access Platform Shell
There are two ways to visit Platform Shell, through a serial connection (Platform console), a through TELNET (network connection).
Use TELNET to visit Platform Shell
1 through TELNET access to the system controller
2, in the main menu system controller type "P" or "0", entered the Platform Shell, a prompt: schostname: SC>,
Process indicated as follows:
Telnet schostname
Trying xxx.xxx.xxx.xxx
Connected to schostname-sc0.
Escape character is'^]'.
System Controller schostname-sc0:
Type 0 for Platform Shell
Type 1 for domain A
Type 2 for domain B
Type 3 for domain C
Type 4 for domain D
Input: 0
Platform Shell
Schostname: SC>
Use the serial port visit Platform Shell
Use the serial port, you can use three kinds of devices to connect.
ASCII terminal
Network Terminal Server
Workstation
Three different from the process equipment
ASCII terminal connected to the system controller serial port, the system controller will be shown the main menu, type "P" or "0", entered Platform Shell.
Connect to the network terminal server (NTS) to the system controller ports, the importation of TELNET order, followed by host name or IP address, system controller there will be the main menu, the loser "P" or "0" P entered Platform Shell.
Workstation
1, the system controller connected to your serial port serial workstations
2, in the prompt SOLARIS tip hardwire input commands to connect to the system controller
3, P input into the platform shell or 0
Visit a domain
Visit domain is the principal means through TELNET (network connection)
Note: Due to a serial port connection is used to connect platform shell, so do not use the serial port to connect domain

DOMAIN shell
If KEYSWITCH is set to (STANDBY or OFF), Victoria had not been activated, then SOLARIS OPENBOOT PROM or operating environment will not be running. If you are running SOLARIS or OPENBOOT PROM mode, then the domain is activated.
Use TELNET order visit domain.
1, the importation of TELNET order, followed by host name or IP address, system controller there will be the main menu, enter 1, 2, 3 or 4 domain type (which can also enter A, B, C or D) to enter DOMAIN Shell.
As follows:
% Telnet schostname
System Controller schostname-sc0:
Type 0 for Platform Shell
Type 1 for domain A
Type 2 for domain B
Type 3 for domain C
Type 4 for domain D
Input: 1
Connected to Domain A
Domain Shell for Domain A
Schostname: A>
2, if the domain is activated, and domain key KEYSWITCH is set to> Hold down the CTRL key, entered TELNET> prompt
In TELNET> prompt, enter send break, from the domain console to the domain shell prompt
As follows:
Ok Ctrl-]
Telnet> send break
Schostname: A>

Below are a description of how to switch between the three:
System Controller platform platform
System Controller domain Shell
System Controller domain console
To go back to the original shell, just enter orders disconnect from the domain Shell to connect to the domain console, resume the importation of orders from the platform Shell switch to the domain Shell console imported under orders.
By entering telnet schostname 500x, you can directly enter the platform shell or
A domain shells or domain console. You can skip to the main menu system controller
In the telnet command, the 5000 is the platform shell, and X is the other figures, as follows:
X is:
1 for domain A
2 for domain B
3 for domain C
4 for domain D
In the console command, domainID is a, b, c, or d.
Here's how SOLARIS environment domain Shell, toggle between openboot prom
SOLARIS assumption is running in the SOLARIS circumstances, the importation
CTRL]
Telnet> send break
Entered the domain Shell,
In the domain Shell, has returned to resume importing SOLARIS environment, such as the importation of break, to openboot prom environment
Note: importing break, then hung SOLARIS environment
Here's how the domain Shell, toggle between openboot prom, assumptions SOLARIS not running
Openboot prom in the> prompt type:
CTRL]
Telnet> send break
> Importing resume, has returned to the environment openboot prom

If the domain has not been activated from the domain Shell to domain console, in the domain Shell setkeyswitch> Domain console domain is activated> Setkeyswitch> From the domain console access to the domain Shell,
OK prompt and type in
Ok CTRL]
Telnet> send break
Should return to the domain console, input
Schostname: A> resume
If the domain has not been activated (SOLARIS, openboot prom is not running), the system controller to remain in the domain Shell, the show
DomainA is not active
Schostname: A>

From the Platform shell into the domain, input console a, as follows:
Schostname: SC> console a
Connected to Domain A
Domain Shell for Domain A
Schostname: A>
If openboot prom in the running, and you will enter a domain console, if the switch-off keyswitch is set to standby, or you will enter a domain A Shell.
(Hint, from the Platform shell into a different domain, the importation of different domain ID, domainID b, c, or d replace a.)

To suspend a session (if you are from the mouth TELNET Ethernet connectivity)
Imported under the domain Shell disconnect order, as follows
Schostname: A> disconnect
Connection closed by foreign host.
Machine_name_prompt%
Your system interrupt controller conversation

To suspend a session (if you are from the serial connection)
If you are connecting the system controller ports, then use the disconnect, suspension system controller conversation, and then use ~. Suspended TIP (TIP for the transmission INTERNET Protocol) sessions. As follows
Schostname: A> disconnect
Connection closed by foreign host.
Machine_name_prompt% ~.
Your system interrupt controller conversation